P.O. Box 267814, Chicago, IL 60626 U.S.A.
Tel: 1-773-465-7285 | Fax: 1-773-465-7387
E-Mail: abt@abtonline.com
|
P.O. Box 267814, Chicago, IL 60626 U.S.A. Tel: 1-773-465-7285 | Fax: 1-773-465-7387 E-Mail: abt@abtonline.com |
      
|
* Malt auger,4 inch diameter with top mounted low RPM motor
* Flexible drop tube
* Floor level hopper with hand guard
* Delivers 33 lbs. per minute
* 1/2 h.p. , 1/2 h.p. , 115/220 V, 1ø, TEFC motor
* Capacity : 13 bbls. working, 13.7 bbls. gross
* 46" O.D., 7.5' overall height
* Insulated and clad on sides
* Shallow cone top, flat sloping bottom to outlet
* Top fittings: manway and CIP ball with shaft
* Side fittings: thermowell; liquid level gauge fittings(2)
* Bottom fittings: 1 1/2" coupling
* 14" S/S legs
* Material: 12 gauge T304 stainless steel
* Internal finish: 2B, welds ground and polished to 180 grit
* External finish: 2B, brushed welds
* Cladding:16 gauge stainless steel with #4 finish or 22 gauge copper
* Bronze head, centrifugal
* 1" NPT discharge, 1 1/4" NPT inlet
* 1 1/2 hp, TEFC motor,230V, 3ø, 5 amps.
* Complete activated carbon water filter with 1.75 cu. ft. activated type PE
natural carbon for removal of trace water contaminants and chlorine, 42 GPM flow rate max.,
30 GPM recommended, 45 psi max. working pressure, 38"high x 21" wide, 1 1/2" inlet/outlet,
c/w bypass and on/off valve.
* Capacity : 7.4 bbls. working, 13.5 bbls gross
* 54" O.D., 8.9' overall height,10' ft. min. ceiling height, 36" floor to bottom of
side manway
* Max. grain capacity 700 lbs., .7 bbl. below false bottom plates, 24-34" grain
bed depth
* 1000 lbs. empty, 3800 lbs. working
* Insulated and clad on sides
* Large top opening hinged manway with handle
* Shallow cone bottom,160° inclusive
* Top fittings: CIP spray ball; sprayball shaft welded with arm to side, cap,
clamp and gasket; 4" ferrule for premasher and sparge devices; 1 1/2" T/C ferrule vapor outlet
* Side fittings: Thermowell, 17" outward opening hinged manway for spent
grain removal
* Bottom: 1 1/2" tri-clamp ferrule outlet
* Polished stainless steel wedge wire two piece false bottom
* Premasher and sparge devices with 3/4" MNPT nipples, clamp and gasket
* 3/4" high temp. hose with quick disconnect set for above
* Wort recycle fitting for CIP shaft
* Legs with flat anchoring pads and shims for leveling
* Material: 12 gauge 304 stainless steel
* Internal finish: 2B, welds ground and 180 grit polished
* External finish: 2B, brushed welds
* Cladding: 16 gauge stainless steel, #4 finish or 22 gauge copper cladding
* System designed to receive wort from mash tun side outlet and transfer it to
the pump
* Valentine arm produces uniform flow without clogging
* Hi-Lo outlets allow reduced hydrostatic pressure across the false bottom and
total draining
* Clear top sight tube allows visible flow control and level detection
* Includes stainless steel pipework, sight glass, valves, clamps, gaskets
* Capacity : 11bbls. working, 15.1 bbls gross, 16" freeboard
* 52" O.D., 8.5' overall height,10' min. ceiling height, 2' floor to bottom outlet
* Insulated and clad on sides
* Top: 2:1 elliptic dished and flanged head with fluted center
* Bottom: flat sloping, 3/16" plate, T316 stainless steel
* Top fittings: Off-center CIP sprayball and shaft to 1 1/2" ferrule ; 3/4" NPT
water inlet coupling at outer vessel edge, 8" I.D. x 6" high steam vent stub with condensate trap
and 1/2" horizontal coupling;17"outward opening top hinged manway; pipe hanger for side
arm
* Side fittings: Thermowell to fit temperature sensor, 1 1/2" T/C tangential
whirlpool inlet, 4" tri-clamp ferrule for cleanout, 1 1/2" T/C outlet
* Lower 19.9 cu. ft. fire box 4" abovefloor; internal 2400°F insulation;
external 1200°F insulation; burner flange; 6" exhaust outlet with damper valve assembly,
access manway; clad with T-304 stainless steel, #4 finish
* Legs with flat anchoring pads and shims for leveling
* Material: 12 gauge 304 stainless steel
* Internal finish: 2B, with welds ground and 180 grit polished
* External finish: 2B, with brushed welds
* Cladding: 14 gauge stainless steel with #4 finish or 22 gauge copper cladding
* 1 1/2" sanitary S/S butterfly valve
* Arm from CIP to tank side: 1 1/2" S/S pipe - 90° T/C connection at CIP
ferrule, 90° bend at tank side down to 1 1/2" T/C end
* 6- 1 1/2" T/C heavy duty clamps and gaskets
* 1 - 1 1/2" T/C cap
* 1 - 1 1/2" x 1 1/2" T/C ended S/S back flow preventer for tangential inlet
* 1 - 4" T/C heavy duty clamp and gasket
* 185,000 - 300,000 BTU/hr. power gas burner with variable BTU input
* U.L. Listed
* NEMA 4 Stainless Steel watertight burner control panel for wall mounting
with: Indicating temperature controller ; Firing rate potentiometer; temperature sensors;
maintain running/ off/ timer by-pass switch; 24 hour timer; fuse, pilot light
* Wort pump on/off switch and run light
* Hot Liquor Pump on/ off switch and run light and temperature gauge
* Cold Liquor Tank indicating temperature controller
* Cold Liquor Pump on/off switch and run light
* Mash Tun LED temperature indicator
* Dual level rectangular work platform
* Stainless steel construction with non slip floor
* OSHA approved handrail on top platform
* Stairs on one side of front
* Master control panel mounted top left
* Liquid flow diverter mounted bottom left
* Wort pump mounted behind diverter panel
* Stainless steel sanitary non overloading centrifugal pump
* 1 1/2" x 1 1/2" tri-clamp inlet and outlets
* 4" open impeller, epdm O rings, replaceable rotating seal
* 3600 rpm, 1 1/2 h.p., TEFC motor
* Mounted on stainless steel work platform
* Polished stainless steel vertical panel with double sided ferrules mounted
* For use in directing all product, water and CIP transfer operations
* Rear fittings for hot and cold water piping
* Two "U" connectors for directing flow,clamps and gaskets
* Mounted on work platform
* Capacity : 13 bbls. working, 13.7 bbls. gross
* 46" O.D., 7.5' overall height
* Insulated, jacketed and clad on sides
* Shallow cone top, flat sloping bottom to outlet
* Top fittings: manway and CIP ball with shaft, 1" (F) NPT cold water inlet
* Side fittings: thermowell; liquid level gauge fittings(2)
* Bottom fittings: 1 1/2" CPLG
* 14" S/S legs
* Material: 12 gauge T304 stainless steel
* Internal finish: 2B, welds ground and polished to 180 grit
* External finish: 2B, brushed welds
* Cladding:16 gauge stainless steel with #4 finish or 22 gauge copper
* High efficiency single stage heat exchanger to cool wort to 54°F using 34°
chilled water
* All wort contact surfaces 316 stainless steel, non clogging plate design
* Painted mild steel frame ends
* 1 1/2 inch tri-clamp product inlet and outlet
* ets
* Polished 304 stainless steel piping, nominal 1 1/2"
* All connections tri-clamp flanged
* All S/S piping from mash tun outlet(s) to pipe grant; grant to diverter; kettle
to diverter; diverter to kettle whirlpo1" coolant inlet and outlet
* 0°F to 210°F S/S thermometer
* Sintered S/S aerating element on T/C cap
* Air line quick disconnects
* Sterile air filter, 0.01 micron with stainless steel wall bracket
* S/S fittings, clamps and gaI.D.
* 6 - 1 1/2" T/C hose ends and S/S clamps
* Capacity : 10 bbls. working, 12.7 bbls gross, 8.5" freeboard to top of straight
side
* 46" O.D., 9'5" overall height,11' min. working height, 1' floor to bottom
outlet
* 1100 lbs. empty, 3800 lbs. working
* Jacketed, insulated and clad
* Top: ASME dished and flanged
* Bottom: 60° included cone insulated and clad
* Top fittings: center CIP spray ball on welded shaft terminask for CIP side
pipe support bracket
* Bottom fittings: Center 1 1/2" tri-clamp ferrule for draw-off
* Working pressure 14.7 p.s.i.
* Material: 12 gauge 304 stainless steel
* Internal finish: 2B, welds ground and 180 grit polished
* External finisol; diverter to CIP; diverter to mash recycle
* Stainless steel sanitary multi position butterfly valve for wort pump
* All necessary multi position butterfly valves, clamps, and gaskets
* 50 ft. high temp reinforced multiply brewers hose, orange, 1 1/2k side at 4'
working height above floor with one 1/4" FPT coupling, one 3/8" MNPT nipple, 1 1/2" T/C end
1 - Side arm support bracket
1 - 0-30 psi pressure gauge -1/4" MNPT
1 - 3/8" S/S ball valve
1 - Quick Disconnect set: 3/8" "
ty : 10 bbls. working, 11.6 bbls gross, 2.2" freeboard to top of straight side
* 42" O.D., 7' overall height, 1' floor to bottom outlet
* 700 lbs. empty, 3500 lbs. working
* Single wall vertical tanks for mounting in cold room
* Top and bottom ASME dting in 1 1/2" tri-clamp; 2 1/2" T/C ferrule for
anti vacuum/pressure relief; 1 1/2" tri-clamp ferrule
* Side fittings: in swing/out swing hinged manway; 1/4" coupling for sample
cock near manway; thermowell, 3/4" NPT glycol inlet/outlets; coupl with 3/8" O.D. hose
connection; 1 1/2" tri-clamp ferrule for sintered stainless steel carbonating element
* Material: 12 gauge 304 stainless steel
* Internal finish: 2B, with welds ground and polished
* External finish: 2B polished
* Other:
1 - 1 1/2" O.D. S/S side arm from CIP to tank side at 4' working height above
floor with one 1/4" FPT coupling, one 3/8" MNPT nipple, 1 1/2" T/C end; top 3/8" O.D. sight
tube connection
1 - S/S sanitary butterfly valve, 1 1/2" T/C ends
10 feet - Clear food grade heavy duty sight hose, 3/8" I.D.
1 - 3/8" S/S ball valve
1 - Quick Disconnect set: 3/8" MNPT insert straight thru design for ball valve
and 3/8" hose barb coupling body, auto shut-off, for 5/16" or 3/8" CO2 line
1 - Pressure gauge, 0-30 psi, 1/4" MNPT
1 - Anti-vacuum/pressure relief valve, 15 psi, 2 1/2" tri-clamp
1 - Sintered S/S carbonating element; 1/4" NPT stainless steel valve
1 - S/S quick disconnect set to fit carbonating element and 3/8" I.D. hose;
1/4" MPT insert and 3/8" hose barb body both with auto shut-off
4 - 1 1/2" T/C heavy duty clamps and gaskets
1 - 2 1/2" T/C heavy duty clamp and gasket
1 - 1 1/2" T/C cap and gasket
* Stainless steel outlet manifolds for connecting three beer lines
* Clamps, valves, gaskets, piping and beverage on/offs
* Digital LED temperature controllers indicate current temperature and set
point
* Thermowell probe and wire included
* Housed in water tight wall mountable control box
* Solenoid valves for glycol piping
* Totally enclosed units for indoor or outdoor use
* Sealed freon primary, secondary circulating glycol
* Adjustable coolant temperature, set at 30°F
* 3 h.p. compressor, 1.5 h.p. circulating pump, 18,000
BTU/hr. @30°F outlet temperature
* 230/60/3ø , 20 amps
* 1 1/4" FNPT plumbing connections
* 48" L x 35"W x 53"H; 450 lbs. working weight
* Stainless steel sanitary non overloading centrifugal pump
* 1 1/2" x 1 1/2" tri-clamp inlet and outlets
* 3 1/2" open impeller, epdm O rings,
* 3600 rpm, 1 1/2 h.p., 220 V, 3ø, TEFC motor, 7 amps.
* Mounted on portable cart with wheels
* 100 ft. clear spiral reinforced suction transfer hose, 1" I.D.
* Two 3/8" I.D. hose barb x quick disconnect body for 5/16" I.D. tubing
* 100 ft. 5/16" I.D. clear gas tubing
* 14 S/S hose clamps, 1 1/2" to 2" O.D.
* Six - 1 1/2" hose ends
* Six -heavy duty 1 1/2" T/C clamps
* Two -1 1/2" T/C caps
* Twenty -1 1/2" T/C hycar gasket
* Horizontal stainless steel leaves hold D.E. on tops only
* Can be shut off without cake falling
* Final filter provides complete recovery of beer at end of filtration
* Tilting filter pack allows quick and easy wash down and cleaning
* Lighted sight glasses, S/S valves, erosion type dosing tank
* Stainless steel h: 2B, brushed welds
* Cladding: 16 gauge stainless steel with #4 finish
* Other:
1 - Anti-vacuum/pressure relief valve
1 - 1 1/2" T/C 90° elbow
1 - S/S sanitary butterfly valve, 1 1/2" tri-clamp ends
1 - 1 1/2" O.D. S/S side arm from CIP to tan x 3/8" ID hose barb quick
disconnect
1 - S/S Perlick sample cock, zwickel, 1/4" MNPT
1 - 2 1/2" T/C heavy duty clamp and gasket
1 - 1 1/2" T/C cap
5 - 1 1/2" T/C heavy duty clamps and gaskets
* Capaciished and flanged heads
* Top fittings: center CIP ball and shaft to 1 1/2" T/C ferrule; pipe hanger for
CIP piping,
2 1/2" T/C ferrule
* Side in swing hinged manway
* Bottom fittings: center 90° elbow ,1 1/2" tri-clamp ferrule terminating
outlet stainless steel pump can be used for separate transfer operations
* 21 sq. ft. filter area, 30-50 bbls. per hour
* 2 1/2 h. p. , 3ø motor
|
|
|
Return to Home Page |
|
Send us e-mail
|
|
|