APPLIED 7 BARREL FULL MASH BREWERY SPECIFICATIONS
ABT MALT CONVEYING SYSTEM
* Malt auger,4 inch diameter with top mounted low RPM motor
* 15 foot drive section
* Flexible drop tube
* Floor level hopper with hand guard
* Delivers 32 lbs. per minute
* 1/2 h.p. , 115/220 V, 1ø, TEFC motor
ABT 7 BARREL SYSTEM HOT LIQUOR (WATER) TANK
* Capacity : 5 bbls. working, 6.7 bbls. gross, to hold sparge water
* 40" O.D., 5.4' overall height
* Insulated and clad on sides
* Dished top and bottom
* Top fittings: manway and CIP ball with shaft
* Side fittings: thermowell; liquid level gauge fittings (2); thermometer, 0-220°F
* Bottom fittings: 1 1/2" coupling inlet / outlet;
* 14" legs
* Material: 12 gauge T304 stainless steel
* Internal finish: 2B, welds ground and polished to 180 grit
* External finish: 2B, brushed welds
* Cladding:16 gauge stainless steel with #4 finish
HOT LIQUOR (WATER) PUMP
* Bronze head, centrifugal
* 1" NPT discharge, 1 1/4" NPT inlet
* 1 1/2 hp, TEFC motor,230V, 3ø, 5 amps.
ACTIVATED CARBON WATER FILTER
* Complete activated carbon water filter with 1.75 cu. ft. activated type PE natural carbon for removal of trace water contaminants and chlorine, 42 GPM flow rate max., 30 GPM recommended, 45 psi max. working pressure, 38"high x 21" wide, 1 1/2" inlet/outlet, c/w bypass and on/off valve.
ABT 7 BARREL MASH / LAUTER VESSEL
* Capacity : 5.2 bbls. working, 9.5 bbls gross
* 46" O.D., 8' overall height,10 ft. min. ceiling height, 35" floor to bottom of side manway
* Max. grain capacity 475 lbs., .4 bbl. below false bottom plates, 24"-33" grain bed depth
* 950 lbs. empty, 2900 lbs. working
* Insulated and clad on sides
* Top: flat and flanged
* Large top opening 17" manway with handle and manway support bracket
* Shallow cone bottom,160° included
* Top fittings: CIP spray ball; sprayball shaft welded with arm to side, cap,clamp and gasket; 4" ferrule for premasher and sparge devices; 1 1/2" T/C ferrule for vapor outlet
* Side fittings: Thermowell, 17" outward opening hinged manway for spent grain removal
* Bottom: 1 1/2" tri-clamp ferrule outlet
* Polished stainless steel wedge wire two piece false bottom
* Premasher and sparge devices with 3/4" MNPT nipples, clamp and gasket
* 3/4" high temp. hose with quick disconnect set for above
* Wort recycle fitting for CIP shaft
* Legs with flat anchoring pads and shims for leveling
* Material: 12 gauge 304 stainless steel
* Internal finish: 2B, welds ground and 180 grit polished
* External finish: 2B, brushed welds
* Cladding: 16 gauge stainless steel, #4 finish
GRANT PIPING SYSTEM
* System designed to receive wort from mash tun side outlet and transfer it to the pump
* Valentine arm produces uniform flow without clogging
* Hi-Lo outlets allow reduced hydrostatic pressure across the false bottom and total draining
* Clear top sight tube allows visible flow control and level detection
* Includes stainless steel pipework, sight glass, valves, clamps, gaskets
ABT 7 BARREL BREWKETTLE / WHIRLPOOL - GAS
* Capacity : 7.7 bbls. working, 10 bbls. gross, 12" freeboard
* 48" O.D., 7.6' overall height, 9 ft. min. working height
* 1000 lbs. empty; 3,100 lbs. working
* Insulated and S/S clad
* Top: ASME shape dished and flanged head
* Bottom: flat sloping, 3/16" plate, T316 stainless steel
* Top fittings: CIP sprayball, welded shaft with 90° elbow to 1 1/2" T/C connection, 3/4" NPT water inlet coupling, 6" steam vent stub with condensate trap and 1/2" coupling, 17" outward opening top hinged manway
* Side fittings: thermowell to fit thermocouple, 1 1/2" tangental whirlpool inlet, 4" tri-clamp ferrule for cleanout,1 1/2" tri-clamp ferrule for wort draw-off
* Lower fire box, internal 2400°F insulation, burner flange, 6" I.D. , 8" O.D. exhaust outlet, insulated access manway
* Material: 12 gauge 304 stainless steel
* Internal finish: 2B, with welds ground and 180 grit polished
* External finish: 2B, with brushed welds
* Cladding: 18 gauge stainless steel with #4 finish
KETTLE GAS BURNER
* 200,000 BTU/hr. power gas burner
* U.L. Listed
ABT BURNER CONTROL PANEL - GAS
* NEMA 4 watertight burner control panel for wall mounting with: Indicating temperature controller with temperature sensor; manual/auto(timer)/off
switch and run light; 24 hour timer; fuse.
* Hot liquor pump on/off switch and run light
WORT PUMP and MOTOR
* Stainless steel sanitary non overloading centrifugal pump
* 1 1/2" x 1 1/2" tri-clamp inlet and outlets
* 3 1/2" open impeller, epdm O rings, replaceable rotating seal
* 3600 rpm, 1 1/2 h.p., 220 V, 1ø, TEFC motor, 10 amps.
* Mounted on stainless steel portable cart with four wheels
* Nema 4 motor starter, cord and plug mounted on cart
HEAT EXCHANGE/ WORT CHILLER
* Single stage heat exchanger to cool wort to within 8°F of cooling liquid
* All wort contact surfaces 316 stainless steel, nonclogging plate design
* Painted mild steel frame ends
* 1 1/2 inch tri-clamp product inlet and outlet
* 1" water inlet and outlet
WORT AERATING SYSTEM
* 0°F to 210°F S/S thermometer
* Sintered S/S aerating element on T/C cap
* Air line quick disconnects
* Sterile air filter, 0.01micron with stainless steel wall bracket
* S/S fittings, clamps and gaskets
ABT BREWHOUSE TRANSFER SYSTEM
* All necessary multiposition butterfly valves, clamps, and gaskets
* 50 ft. high temp. reinforced multiply brewers hose, orange, 1 1/2" I.D.
* 6 - 1 1/2" T/C hose ends and S/S clamps
ABT 7 BARREL FERMENTATION/CONDITIONING VESSELS
* Capacity: 6.5 bbls. working, 7 bbls. gross, 5" freeboard
* 42" O.D., 6' overall height, 6 1/4" floor to bottom outlet
* 700 lbs. empty, 3500 lbs. working
* Top and bottom: Dished and flanged heads
* Jacketed, insulated & clad:
- Jacketed - 3/4" S/S glycol inlet/outlet couplings
- Insulated - 2" on side
- Clad - #4 finish S/S on side
* Internal volume calibrations
* Top fittings: 3" triclamp fitting & 3/8" FNPT coupling in top lid; (2) sight glasses
* Side fittings: Thermowell for temperature controller probe
* Bottom fittings:1 1/2" triclamp drawoff ferrule; 1 1/2" triclamp totally draining center outlet and pipe to vessel side
* Mild steel painted legs
* Other:
1 - Top lid gasket and clamp
1 - 3" triclamp to grundy valve fitting adapter
1 - New grundy pressure relief/anti-vacuum valve with pressure gauge,
bronze ball valve,CIP shaft and sprayball
1 - 1 1/2" triclamp x 1/2" MPT adapter for CIP inlet
1 - Sanitary S/S 1 1/2" T/C butterfly valve
1 - Set of quick disconnects 3/8"MNPT x 3/8" tubing-both auto closing
1 - One quick disconnect to fit tank disconnect x 3/8" hose barb, straight through-open
1 - 3" triclamp clamp and gasket
4 - 1 1/2" triclamp clamps and hycar gaskets
2 - 1 1/2" triclamp caps
GLYCOL CHILLER SYSTEM
* Totally enclosed units for indoor or outdoor use
* Sealed freon primary, secondard circulating glycol
* Adjustable coolant temperature, set at 30°F
* 2 h.p. compressor, 1/2 h.p. circulating pump, 15,000 BTU/hr. @30°F outlet temperature
* Capacity to cool up to 28 bbls. from 60°F to 36°F in 24 hours and maintain 35 bbls. at 36°F and remove the heat of fermentation from 14 bbls. fermenting lager beer; 5,000 BTU/hr. excess cap.
* 230/60/3ø, 20 amps
* 1/2" NPT plumbing connections
* 28" L x 25"W x 57"H; 450 lbs. working weight
ABT TEMPERATURE CONTROLLERS
* Digital LED temperature controllers indicate current temperature and set point
* Thermowell probe and wire included
* Housed in water tight wall mountable control box
* Solenoid valves for glycol piping
PLATE AND FRAME SHEET FILTER
* 40 cm x 40 cm stainless steel plate and frame holds upto 24 sheets
* 18 plates for 17 sheets
* Filters 7-10 barrels per hour
* Inlet/outlet valves - 1 1/2" tri-clamp
* Stainless sanitary valves, pressure gauges, sample valve
* Lower drain pan
* Portable on wheels
* 6 grades of filter pads available
ABT 7 BARREL RECONDITIONED SERVING TANKS
* Capacity: 7 bbls. working volume
* 38" O.D., 6' overall height, 6 1/4" floor to bottom outlet
* 700 lbs. empty, 3500 lbs. working
* Single shell polished
* Internal volume calibrations
* Top: Dished and flanged, Grundy valve fitting, 3/8" NPT CO2 inlet coupling
* Two top dish sight glasses
* Grundy anti-vacuum pressure relief valve with pressure gauge, ball valve and 1 1/2" T/C to ball valve adapter for CIP, CIP sprayball and shaft
* Bottom fittings: 1 1/2" T/C above bottom ferrule and sintered stainless steel carbonating element; 1 1/2" T/C triclamp bottom outlet
* Sanitary S/S 1 1/2" T/C butterfly valve
* Stainless steel 1/4" valve for carbonating stone inlet
* Quick disconnect sets(2) for top fitting, carbonating stone, gas transfer
* Three 1 1/2" T/C heavy duty clamps and gaskets
* Mild steel painted legs
SERVING TANK OUTLETS
* Stainless steel outlet manifolds for connecting three beer lines
* Clamps, valves, gaskets, piping
SET OF CELLAR EQUIPMENT
* 100 ft. clear spiral reinforced suction transfer hose, 1 " I.D.
* One set 3/8" NPT x 3/8" I.D. quick disconnect
* 14 S/S hose clamps, 1 1/2" to 2" O.D.
* Six - 1 1/2" hose ends
* Six -heavy duty 1 1/2" T/C clamps
* Two -1 1/2" T/C caps
* Twenty -1 1/2" T/C hycar gaskets
ABT BASIC PUB BREWERY LABORATORY PACKAGE
